Shop Counter Culture DIY UV resin, curing lamps, colorants and kits for jewelry, keychains, doming, transparent molds and other small craft projects. Our clear UV resin is a ready-to-use, one-part formula that cures when exposed to compatible UV light, so there is no resin-to-hardener ratio to measure.
Choose the right UV resin product
| Product |
What it includes |
Best for |
| Clear UV Resin |
Medium-viscosity, one-part resin in 4 fl oz, 8 fl oz, 16 fl oz and 32 fl oz sizes |
Makers who already own a compatible lamp and need resin for jewelry, keychains, doming, pens, embellishments or small transparent molds |
| UV Resin Kit with 48W Lamp |
Clear UV resin in the selected size plus the foldable 48W curing-lamp system |
New makers and anyone who needs a coordinated resin-and-light setup |
| 48W Foldable UV Resin Curing Lamp |
Two detachable lamp sections, clear shelves, two USB-C cords and 2-, 3- and 5-minute timers |
Makers who already have resin but need a flexible dual-sided curing station |
| Spectrum Resin Dye Set |
Twenty alcohol-free liquid colorants compatible with UV resin and properly mixed two-part epoxy |
Adding controlled color while preserving light and layered detail |
| Resin Sample Kit |
Artist Resin, medium-viscosity Artist Resin, Fast Set Epoxy and UV Resin samples |
Comparing resin formulas before purchasing a larger size; a UV lamp is not included |
What can you make with UV resin?
- Pendants, earrings, charms and open-bezel jewelry
- Keychains, zipper pulls, ornaments and phone-grip decorations
- Domed decals, labels and small pieces of artwork
- Resin pens, tumbler-topper pieces and embellishments
- Dried-flower, glitter and decorative inclusions in thin layers
- Small transparent molds, surface details and light-accessible repairs
UV resin is intended for small or shallow projects where light can reach the complete resin area. It is not the right formula for large coatings, deep molds or opaque molds that block curing light.
UV resin curing basics
UV resin performs best in thin layers. For clear work, use layers around 1-2 mm (0.04-0.08 inch) whenever possible. Clear resin in a transparent mold can be applied up to about 3 mm (about 1/8 inch) per layer.
With both sections of the Counter Culture DIY 48W lamp operating, begin with an estimated 2-3 minute curing cycle. If using one lamp section, begin with approximately 4-5 minutes. Resin depth, color, glitter, inclusions, lamp distance, wavelength, coverage and mold transparency can all affect curing time.
After the initial cycle, check the entire piece. If any area is not completely hard and non-tacky, continue curing in additional one-minute cycles. Build projects deeper than 3 mm (about 1/8 inch) in separately cured layers.
How to use UV resin
- Prepare a clean, dry project on a level work surface.
- Apply clear resin in a thin layer so UV light can reach the complete area.
- Add compatible colorants and inclusions sparingly. Dark colors, heavy pigment and dense glitter can block light.
- Center the project within the lamp's coverage and cure using the appropriate starting cycle.
- Inspect the piece and add one-minute cycles until it is fully hard and non-tacky.
For complete supplies, application steps, project ideas and troubleshooting, read How to Use UV Resin: The Ultimate Guide.
UV resin or two-part epoxy?
Choose UV resin for small, shallow projects, detail work and doming when you want to control exactly when curing begins. Choose a two-part coating resin for larger artwork and surface coatings, or a casting resin designed for deeper molds and flower preservation. Standard two-part epoxy cures through the measured reaction between resin and hardener; a UV lamp does not cure it.
UV resin questions
Does UV resin need to be mixed?
No. Counter Culture DIY UV Resin is a one-part formula that cures with compatible UV light. Do not mix it with epoxy hardener.
What molds work with UV resin?
Transparent molds and open surfaces work best because UV light must reach the resin. Opaque molds can block the curing light and leave uncured areas.
Can I color UV resin?
Yes. Use a compatible resin colorant such as Spectrum Dye. Darker colors and heavier color loads generally require thinner layers or additional curing time.
Why is my UV resin still tacky?
The complete resin area might not have received enough compatible UV light. Check the layer depth, pigment load, glitter, inclusions, lamp distance, coverage and mold transparency, then continue with additional one-minute curing cycles.
Can the 48W lamp cure regular two-part epoxy?
No. Two-part epoxy cures through a chemical reaction between resin and hardener. The lamp is intended for compatible UV-curable materials.
Safety and storage
Wear gloves, work in a well-ventilated area and avoid skin and eye contact with uncured resin. Do not stare directly into operating UV lights. Keep resin tightly closed and stored upright in a cool, dark place away from sunlight and other UV sources. Follow the product labels and safety information supplied with the resin, colorants and lamp.
